Direct-drive series installed on ISO 5211 platform specification valves (valves))
Professional certification
ISO 9001、CE、CSA、UL429、IP67
-
-
Direct-drive electric motor actuators must be installed on ISO 5211 high-platform valves or butterfly valves
-
UM/R series electric motor actuators are low-power, high-torque devices
-
Sealed casing with waterproof seals, certified to IP67, suitable for installation in various outdoor environments
-
Smooth opening speed effectively prevents water hammer phenomenon, increasing the lifespan of pipe fittings
-
UM/R series electric motor actuators can be viewed from the top window or side to check valve position, or through wiring control boxes with indicator lights displaying position
-
Waterproof rating IP67
-
Casing made of materials such as "NYLON" with characteristics of high temperature resistance, acid and alkali resistance, and impact resistance
-
Aluminum alloy casing available as an optional purchase
Optional Accessories-
Temperature controller
-
Non-electrical micro switch (up to 2 sets)
-
Heater (including overheat protector)
-
Proportional controller
-
On-site control
-
Relay
-
Potentiometer (VR set)
Precautions-
When operating manually or during maintenance, always turn off the power first to prevent component damage and hazards. When using manual operation, it is recommended to use a wrench (8mm opening) with a length not exceeding 10 cm. Turn gently; if it feels tight, check if the valve body is locked before proceeding. Do not use excessive force to turn, as this may damage internal components.*Do not use other rods to rotate the handwheel, as this may damage the electric motor actuator and valve
-
After completing wiring work, check if the waterproof device (O-ring) is in place before tightening the casing. Ensure that the cable gland screws are securely tightened to prevent dust or rainwater ingress. (It is recommended that customer wiring should be a minimum of 6mm in diameter or larger.))
-
If two or more electric valves need to open or close simultaneously, install a relay for each valve. Do not connect them in series or parallel
-
When operating manually, ensure that the window pointer does not exceed the scale range to avoid damaging internal components. (For proportional controllers: variable resistor (VR) damage may occur.)
-
-
Weight1.6 kgManual device8mm open-end spannerFlange hole distance（ISO 5211）F03/F05 F04 F05/F07
左右滑動看表格Model Motor power 90° Rotation Switch Time(sec) Torque value(±5%)
kgf-cm
AC110V(60Hz)Torque value(±5%)
kgf-cm
AC220V(60Hz)No-load current consumption AC
100V~120VAC
200V~240VUM-1 10W 1 75 80 0.6A 0.3A UM-1 10W 5 181 214 0.6A 0.3A UM-1 10W 10 350 362 0.6A 0.3A UM-1 15W 1 127 132 0.7A 0.4A UM-1 15W 10 410 432 0.7A 0.4A 左右滑動看表格Model Motor Power 90° Rotation Switch Time(sec) Torque Value(±5%)
kgf-cm
DC24VNo-Load Consumption Current DC24V UM-1 10W 2.5 250 0.1A UM-1 10W 15 400 0.1A
Rated voltage(special voltages available on request)-
AC 100V ~ 120V
-
AC 200V ~ 240V
-
DC 24V
-
-
Product Features Introduction
-
Direct-drive electric motor actuators must be installed on ISO 5211 high-platform valves or butterfly valves
-
UM/R series electric motor actuators are low-power, high-torque devices
-
Sealed casing with waterproof seals, certified to IP67, suitable for installation in various outdoor environments
-
Smooth opening speed effectively prevents water hammer phenomenon, increasing the lifespan of pipe fittings
-
UM/R series electric motor actuators can be viewed from the top window or side to check valve position, or through wiring control boxes with indicator lights displaying position
-
Waterproof rating IP67
-
Casing made of materials such as "NYLON" with characteristics of high temperature resistance, acid and alkali resistance, and impact resistance
-
Aluminum alloy casing available as an optional purchase
Optional Accessories-
Temperature controller
-
Non-electrical micro switch (up to 2 sets)
-
Heater (including overheat protector)
-
Proportional controller
-
On-site control
-
Relay
-
Potentiometer (VR set)
Precautions-
When operating manually or during maintenance, always turn off the power first to prevent component damage and hazards. When using manual operation, it is recommended to use a wrench (8mm opening) with a length not exceeding 10 cm. Turn gently; if it feels tight, check if the valve body is locked before proceeding. Do not use excessive force to turn, as this may damage internal components.*Do not use other rods to rotate the handwheel, as this may damage the electric motor actuator and valve
-
After completing wiring work, check if the waterproof device (O-ring) is in place before tightening the casing. Ensure that the cable gland screws are securely tightened to prevent dust or rainwater ingress. (It is recommended that customer wiring should be a minimum of 6mm in diameter or larger.))
-
If two or more electric valves need to open or close simultaneously, install a relay for each valve. Do not connect them in series or parallel
-
When operating manually, ensure that the window pointer does not exceed the scale range to avoid damaging internal components. (For proportional controllers: variable resistor (VR) damage may occur.)
-
-
Specification SheetWeight1.6 kgManual device8mm open-end spannerFlange hole distance（ISO 5211）F03/F05 F04 F05/F07 左右滑動看表格
Model Motor power 90° Rotation Switch Time(sec) Torque value(±5%)
kgf-cm
AC110V(60Hz)Torque value(±5%)
kgf-cm
AC220V(60Hz)No-load current consumption AC
100V~120VAC
200V~240VUM-1 10W 1 75 80 0.6A 0.3A UM-1 10W 5 181 214 0.6A 0.3A UM-1 10W 10 350 362 0.6A 0.3A UM-1 15W 1 127 132 0.7A 0.4A UM-1 15W 10 410 432 0.7A 0.4A 左右滑動看表格Model Motor Power 90° Rotation Switch Time(sec) Torque Value(±5%)
kgf-cm
DC24VNo-Load Consumption Current DC24V UM-1 10W 2.5 250 0.1A UM-1 10W 15 400 0.1A
Rated voltage(special voltages available on request)-
AC 100V ~ 120V
-
AC 200V ~ 240V
-
DC 24V
-